Reinitialize your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a easy process that can be completed in just a few procedures.

• Begin by ensuring your red dot sight is activated.
• Identify the small button for reset on the rear of the unit.
• Use a paperclip to depress the reset lever for approximately 7 moments.
• Release the switch and your Holosun EPS Carry Red Dot sight will restart.
• Your red dot sight should now be reverted to its factory settings.

Reset Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it back to standard configuration is a breeze. First, locate the tiny button on the side of your optic. Then, keep pressed it for around five seconds until you see the indicator light change. Your Holosun EPS Carry is now reset to its factory settings, ready for precise aiming.

restore Your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you more info begin, remember to disconnect the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

• Simultaneously press and hold the power button for approximately 7 seconds.
• The display will flash, indicating that the reset is successfuly initiated.
• Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and confirm your sight's functionality. If you encounter any further problems, don't hesitate to reach out to their technical assistance.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

• Initially, Turn on your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, activate the power button once.
• You will show a confirmation prompt indicating that the reset process is initiated.
• Allow the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Clear All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Restore your Holosun EPS Carry through a Factory Original Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the fix. This will restore your sight to its factory settings, clearing any personalized configurations you've made. To accomplish this reset, adhere to these simple steps:

• Initially, locate the reset switch on your EPS Carry.
• Then, use a fine object, like a paperclip, to depress the reset lever.
• During keep the reset switch pressed, power on your EPS Carry.
• The sight will blink a message showing that the reset is successful.

When the reset is finished, your EPS Carry will be back to its factory settings.

Report this wiki page